環氧樹脂地坪施工環境要求

1.環氧樹脂地坪施工環境要求：環氧樹脂地坪施工作業現場,環氧樹脂地坪涂料施工環境要求為：相對濕度小于百分之80，溫度需在10至35攝氏度范圍內環氧樹脂地坪施工環境要求，通常環氧樹脂地坪涂料施工環境要求為：相對濕度小于百分之80，溫度需在10至35攝氏度范圍內。超出此范圍需選用特殊環氧樹脂地坪涂料種類。環氧樹脂地坪涂料（特別是面漆）涂裝與固化過程中（表干前），底材外表溫度應高于露點3攝氏度以上，以防底材及濕膜外表水汽凝結影響涂層附著力和外表作用。 

環氧樹脂地坪施工環境要求

2.夏季在清晨或傍晚施工較為宜。施工時需測量溫度，當氣溫超過35度時，為了施工人員的健康和優質的涂膜質量，應避免施工。在濕度大和雨天施工，需測量相對濕度和露點溫度，隨時查看已干燥涂膜的質量，當呈現裂紋、橘皮、脫落等現象時，及時補涂維修。對于雙組分涂料，在配制稀釋劑和固化劑時應盡量選用慢蒸發溶劑，混合甲乙組分時，選用少數、多次勤配的原則，避免呈現涂料固化中放熱過快的現象而引起涂料作廢。溫度過高，雙組分涂料特別是無溶雙組分涂料易呈現爆聚現象，即涂料反應過快，很多放熱而使涂料使用期縮短。

高溫安檢門下施工進，雖然涂料干燥速率會較快，但即便測定已實干，也要按照必定的涂裝距離進行下一道涂裝。